General Description. The LP and LP are micropower voltage regulators with very low dropout voltage (typically 40mV at light loads and mV at. LPLPRE3 Texas Instruments LDO Voltage Regulators FIXED MICROPWR VLTG REG datasheet, inventory, & pricing. The LP and LP are micropower voltage regulators with very Careful design of the LP/LP has minimized all . See MIL/AERO Datasheet.

Author: Shakazuru Muzshura
Country: Moldova, Republic of
Language: English (Spanish)
Genre: Travel
Published (Last): 1 October 2004
Pages: 111
PDF File Size: 2.36 Mb
ePub File Size: 4.41 Mb
ISBN: 526-9-81860-844-1
Downloads: 15723
Price: Free* [*Free Regsitration Required]
Uploader: Akira

The program currently occupies out of bytes of program memory.

National Semiconductor – datasheet pdf

I could post the entire project if you think it would help sales of the ATtiny26 board I do intend to buy a few more — the sale price is very attractive, so be sure and save me a couple! What puzzles me is that the regulator encounters this situation every time the external source is switched off and there are capacitors in the l2950 that must be discharged, so there is some reason pp2950 think that such a transient backflow is not damaging.

There is a small current draw increase at 5. If I connect the 4. The board is datasyeet below. Beta and gamma radiation are much more penetrating so the direction the tube is pointing is less important and is actually irrelevant for gamma radiation. In my version, the tube is screened so that small sources can be set right on top of the detector. The unit is currently monitoring the cosmic background radiation in my dztasheet 95 counts in seconds.

It looks like the detector is on the same side as the display – does this mean you are checking yourself for radiation rather than pointing it at a source in front of you?

Datasheets search archive of electronic components datasheets

Both have a thin and very delicate metalized membrane for measurement of alpha radiation. Can you try doing the regulator test again?


Since there is some interest, my Geiger counter is based on a circuit described by Tom Napier in Circuit CellarNovember Thanks for checking on the regulator — maybe I shorted the power supply while hooking things up. I can always use diodes to switch between solar and backup supply, but I thought I could float charge the battery datashet such trickery. I just tried taking a regulator part not on a lp950 and applied from 4.

The C program and the two buttons provide a menu-based system to set up data collection parameters and do the counting. If only the ATtiny26 had a bit more memory… Thanks, Jim. See below for the exterior appearance. We even had some ATmega8 versions made, but we never sold them there were some other factors besides the ATtiny26 board not doing well, such as the mega coming out and the move to 6-pin ISP connectors.

I especially like the plated through holes, which are fantastic for prototyping if you have to remount components several times. I datasheett intend to buy a few more — the sale price is very attractive, so be sure and save me a couple! We would probably buy a few, especially if the footprint was compact.

The JTAG fuse comes set, which makes some pins start up set high. The counter input INT0 is marked with a green arrow. My most recent project with the ATtiny26 board is a Geiger counter. I suspect that no long term damage should result from this misuse, as long as one does not exceed other component ratings. I had to jump! Where did you get your Geiger tube? I expect that the regulator can tolerate this but it might add some unnecessary current drain. I could post the entire project if you think it would help sales of l;2950 ATtiny26 board.


National Semiconductor

Shop Blog Forum Support. The HV generator is top right, datwsheet to the connector for the V tube bias red arrow. The LP data sheet does not give any insight into this situation.

Can you tell me what you like about it? Did you look at the datasheet from that company? By the way, there are a few manufacturers of the part, and your board probably has the one from On Semiconductor. For one low-power project, I have the possibility of powering the board from either a 9V solar cell or a 4.

Well, I connected a 4. My power supply current-limited at about 1 amp. Of course we had these boards made in a batch, so now each time I datasyeet one I have to bypass the power switch with tweezers to to clear that fuse.

LP Datasheet Alpha Semiconductor pdf data sheet FREE from

The rainbow cable leading off screen goes to the two pushbuttons and the LCD. It features an internal V power supply 2 mA total draw! By the way, I really like the board design. There is one error in the published circuit: I do that sort of thing all the time, and I have had no problems. Is the RS option useful? What I like about the ATtiny26 board is the convenient arrangement of two ports with access to power and ground at several points, coupled with the well-laid out prototyping area.

Not realizing this we designed our main board which uses the pushbutton power switch with one of these connected to the OFF pin. Fortunately, I disconnected it quickly enough to prevent any obvious permanent damage to the regulator.